Products

Descriptions: Measurement of relevant climatic data is becoming more and more important. This Humidity & Temperature Indicator offer very accurate measurement of Relative Humidity and Temperature by Excellent readability of the very high intensity seven segment LED display. The Humidity & Temperature Indicator housed with roughest case allow the use in tough industrial environments, Latest technology and well proven sensor guaranteed highest accuracy and long term stable measurement. Model : HT 191J Display : 4+4 Digit 2' or 4' or 8' Seven Segment LED Display Range : 0-60°C 0-100%RH (Depends on Sensor) Resolution : 0.1 or 0.01 C / 0.1% RH Accuracy : Depends on Sensor Mounting : Wall Mountable Operating Temp.& Humd : 0-50°C/20 to 95% RH Non Condensing Power Supply : 230V AC 50Hz Weight : 5kg (Approx..)

Model: PIJ – 542 A1 Display: 2” or 4” or 8” 4 Digit 7 segment RED LED* Accuracy: ± 0.1 % of FS Analog inputs: 4 – 20 mA, 0 - 20 mA, 0 to 70 mV, 0 to 10 V DC, 0 – 400 Ω (H & L Limit Programmable) Temperature inputs: RTD - PT 100, Thermocouple - J, K, R, S, T, B, N, E Analog display range: -1999 to 9999 (H & L Limit programmable) Temperature range (H & L Limit programmable): RTD - PT 100 (-199.9 to 850.0°C / -199.9 to 999.9 °F) TC - J (- 200 to 1200°C / -328 to 2192°F) TC - K (- 200 to 1372°C / -327 to 2501°F) TC - R (- 40 to 1768°C / -40 to 3214°F) TC - S (- 40 to 1768°C / -40 to 3214°F) TC - T (- 200 to 400°C / -328 to 752°F) TC - B (300 to 1820°C / 572 to 3308°F) TC - N (-200 to 1300°C / -327 to 2372°F) TC - E ( -200 to 999.9°C / -327 to 1832°F) Unit selection: °C / °F ( for RTD & TC inputs) Analog input display resolution: 0.001 / 0.01 / 0.1 / 1 (Selectable) Temperature resolution: 0.1 / 1 °C / °F (optional 0.01 for RTD - PT 100 I/P up to 99.99 °C Factory presetable) Filter constant: 1 – 100% (Adjustable) Display hold option: Peak, hold & average (any one selectable) Hold delay: 0 - 999 sec (selectable) Relay Output (optional): 2 Relay (5A rated) with 6 Relay Status Selection, Adjustable, Hysteresis, Cyclic Delay Temperature drift: ≤ 0.1% FS/°C (typical 50 ppm) Re Transmission (optional): Opto Isolated Analog Output 4 - 20 mA or 0 - 10V DC PC communication (optional): RS 485 (2 wire) MODBUS RTU protocol PC interface software: Optional Sensor Supply (external): 24 V DC ±10% @ 100 mA Power supply: 230 V AC / 50 Hz Overall dimension: 428 x 171 x 85 (L x H x D) mm (Approx.) Housing : MS Powder coating Mounting: Wall or sealing with 360 º rotatable clamp Operating environment: 0 - 50°C / 5 to 95% RH Non condensing Weight (Approx.): 4.5 kg

Model: PIJ – 542 C1 Display: 2” or 4” or 8” 4 Digit 7 segment RED LED* Accuracy: ± 0.1 % of FS Analog inputs: 4 – 20 mA, 0 - 20 mA, 0 to 70 mV, 0 to 10 V DC, 0 – 400 Ω (H & L Limit Programmable) Temperature inputs: RTD - PT 100, Thermocouple - J, K, R, S, T, B, N, E Analog display range: -1999 to 9999 (H & L Limit programmable) Temperature range (H & L Limit programmable): RTD - PT 100 (-199.9 to 850.0°C / -199.9 to 999.9 °F) TC - J (- 200 to 1200°C / -328 to 2192°F) TC - K (- 200 to 1372°C / -327 to 2501°F) TC - R (- 40 to 1768°C / -40 to 3214°F) TC - S (- 40 to 1768°C / -40 to 3214°F) TC - T (- 200 to 400°C / -328 to 752°F) TC - B (300 to 1820°C / 572 to 3308°F) TC - N (-200 to 1300°C / -327 to 2372°F) TC - E ( -200 to 999.9°C / -327 to 1832°F) Unit selection: °C / °F ( for RTD & TC inputs) Analog input display resolution: 0.001 / 0.01 / 0.1 / 1 (Selectable) Temperature resolution: 0.1 / 1 °C / °F (optional 0.01 for RTD - PT 100 I/P up to 99.99 °C Factory presetable) Filter constant: 1 – 100% (Adjustable) Display hold option: Peak, hold & average (any one selectable) Hold delay: 0 - 999 sec (selectable) Relay Output (optional): 2 Relay (5A rated) with 6 Relay Status Selection, Adjustable, Hysteresis, Cyclic Delay Re Transmission (optional): Opto Isolated Analog Output 4 - 20 mA or 0 - 10V DC PC communication (optional): RS 485 (2 wire) MODBUS RTU protocol PC interface software: Optional Sensor Supply (external): 24 V DC ±10% @ 100 mA Power supply: 230 V AC / 50 Hz Overall dimension: 760 x 320 x 85 (or) 1125 x 320 x 85 (L x H x D) in mm (Approx.) Housing : MS Powder coating Mounting: Wall or sealing with 360 º rotatable clamp Operating environment: 0 - 50°C / 5 to 95% RH Non condensing Weight (Approx.): 7.5 (or) 8.5 kg

16 Characters LCD Display mV / mA / Volt Analog Inputs Wide Input Ranges ± 75mV / ± 10V Wide Display Ranges - 199999 to +199999 Parameter & Unit Display User Front Configurable 2 Relay Outputs with Configurable H / L Setting(Optional) Re Transmission Output (Optional) 24 V DC Sensor Supply Universal Supply Voltage 90 to 270V AC / DC

Model : pH 641 Display : 0.5” 3 ½ Digit 7 segment Red LED Range : 0 to 14 pH / -1999 to 1999 ORP Input Impedance : > 10¹² Ohms Accuracy : ± 0.01 pH ± 1 digit / ± 1 ORP ± 1 digit Resolution :0.01 pH Electrode: Combined Electrode with BNC attachment Input connection : BNC socket Operating Environment : 0 to 50 °C / 20 to 95 % RH non condensing Power supply : 230V AC / 50 Hz ± 10% Overall Dimension in mm : 48 x 96 x 65 (H x B x L) Cut out Dimension in mm : 44 x 92 (H x B) Instrument Weight : 170 g

Model : CC 100 Display : 0.5” 4 Digit 7 segment Red LED Range :0 to 9999 counts Input : Count Pulse for Electronic Marker Pen Resolution : 1 count Disk Diameter : 110 mm Magnification : x1.7 Surface Count Reset : Push Button Provided on front panel Input connection : 2 Pin Female Socket Operating Environment : 0 to 50 °C / 20 to 95 % RH non condensing Power supply : 230V AC / 50 Hz ± 10% Overall Dimension in mm : 220 x 200 x 105 (L x B x H) Instrument Weight : 2.5 kg (Approx.)

Model :DN 1000 Display : 0.5” 3 ½ Digit 7 segment Red LED Range : 0 to 19.9 & 199.9 NTU Resolution : 0.1 NTU Detector : Photo Diode Test Tube : 30mm Dia Clear Glass Test tube x 4 nos Light Source : High Intensity 5mm White LED Operating Environment : 0 to 50 °C / 20 to 95 % RH non condensing Power supply : 230V AC / 50 Hz ± 10% Overall Dimension in mm : 220 x 200 x 110 (L x B x H) Instrument Weight : 1.7 kg (Approx.)

Model: Pcal 1300 / 700 bar Range (bar): 0 to 700 bar Pressure media: Oil & Water Pressure pump: CT – 02 Display: 128 × 64 COG Graphic LCD with White LED Backlight Resolution (bar): 6 digit user selectable Instrument Port: ½” BSP Male x 10 mm long Instrument dimension: 100 × 100 × 55 (W × H × D) mm Instrument Weight: 400 gms (Approx.) Stability time: 1 to 2 mins Accuracy: ± 0.05% FS Pressure units * (selectable): bar, mbar, MPa, kPa, Pa, PSI, kg/cm², inHg, cmHg, mmHg, mH₂O, ftH₂O, inH₂O, cmH₂O, mmH₂O Pressure Zero: One touch zero provided on front key Pressure Peak: Maximum & minimum with user reset option Pressure overflow: FS X 2 (Max.) Pressure burst: FS X 3 (Max.) Temp.Measure: RTD - PT 100 (2,3,4, wire selectable) Temp. Range: -199.999 to 850.000 mA Measure: 0-24 mA (scalable) Display scale: -99999 to 99999 counts (for mA measure input) Switch test: Provided Display Hold: One touch hold provided on front key Power Supply: 9V DC ±5% / 600 mAh Rechargeable battery with battery life 20 hours without backlight (or) 9V DC adapter / 230V AC supply operated Pump Weight (Approx.): 14 kg PC Interface (optional): RS-485 (2 wire) (Note: connect to PC using USB to RS 485 converter supplied along with PC software) PC Software (optional): Windows-based semi-automatic calibration software (Optional)

Model: DCM 200 Display: 0.5” 3 ½ Digit 7 segment Red LED Range: 0 – 20 μS/ 200 μS/ 2000 μS/ 20 mS / 200 mS ( 5 range selection using front rotary switch ) Resolution: 0.01 / 0.1 / 1 for μS range & 0.01 / 0.1 for mS range Accuracy: ± 1 % of Range ± 1 digit Temperature Compensation: 0 to 50°C (Manual) continuously adjustable Cell Constant: Adjustable with indication on display Sensor: Platinum Conductivity cell (1.0 cell constant) with Banana male connector Input Connection: Banana socket Operating Environment: 0 to 50 °C / 20 to 95 % RH non condensing Power supply: 230V AC / 50 Hz ± 10% Overall Dimensions in mm: 185 x 235 x 65 ( L x B x H ) Instrument weight: 1.6 kg (Approx.)

Model : TCAL 1503 / -100 Display : 4.3” True colour TFT display with touch screen Temperature Range : -100°C to 40°C @20°C to 30°C Ambient Resolution : 0.01 °C Block Stability (30 mins) : Better than ± 0.03°C at full range Block Radial Uniformity : ± 0.05 °C at full range Temperature Read out : °C / °F (selectable) Heating time : 25°C to 40°C : 30 min -100 to 25°C : 80 min Cooling Time: 25°C to -100°C : 85 min 40 to 25°C : 12 min Stabilization time : 15 minutes Insert Dia. x Height: 30 x 120 mm Test sensor immersion depth: 115 mm Standard well holes in mm : Insert No. 1 : 5.1, 6.2, 6.2 & 8.1 Insert No. 2 : 6.2, 6.2 & 10.2 Measure inputs: RTD – PT 100, PT 1000, TC – J, K, R, S, T, E, B, N , Analog – mA, V, mV, Ohms Cold junction Accuracy: ± 0.3°C Communication: RS 485 MODBUS Switch Test: Provided Sensor supply output: 24V DC ± 10% / 50mA max. Power supply: 230V AC ± 10% / 50Hz (Optional 110V AC) Power Consumption : 500 VA Overall Dimension in mm : 356 x 210 x 534 (L x B x H)(Approx.) Instrument Weight :15.9 kg(with well insert)(Approx.)

Model: HTD 200 Display: 2.8” True colour TFT display with touch screen Range: Temperature: -40 to 85 °C (T), Humidity: 0 to 100% RH (RH) Resolution: 0.01 °C / 0.01 % RH Accuracy at 23 °C± 5 °C : ± 0.2 °C / ±0.8 % RH Psychometric calculated indication: Dew / Frost point ( Dp / Fp ) Wet Bulb Temperature ( Tw ) Vapour partial pressure ( E ) Vapour Saturation pressure ( Ew ) Mixing ratio by weight (dry) ( g / kg ) Enthalpy ( H ) ( KJ / kg ) Specific Humidity (moisture) ( g / kg ) Absolute Humidity (moisture) ( g / m³ ) Volume mixing ratio (dry) ( ppm ) Calculation method: WMO method Display refresh rate: 1 s (typical) Calibration : 5 point lookup table for both Temperature & Humidity Alarm: Audible & Visible user settable individual High & Low alarm set with alarm mode selection for all the 3 parameters Touch sound: On / Off option available Logging interval: 1 sec to 24 Hrs programmable Memory capacity: 4 to 32 GB Internal storage Data download: Via USB Battery charging port: USB C type Integrated battery: 3.7V / 10,000 mAh Inbuilt rechargeable polymer Li-ion battery Backlight time interval: 0(OFF) to 59 mins : 59 secs (user adjustable) Brightness adjustment: 10 to 100% (user adjustable) Application environment range: -10 to 60 °C / 0 to 100% RH (non condensed) Storage environment range: -10 to 45 °C / 10 to 90% RH Housing material: ABS with anti-slip grip silicon cover Protection class: IP40 Overall Dimension in mm: 35 x 80 x 165 mm ( L x B x H) Instrument Weight: 560 g (Approx.)

Model : TCAL 1503 / -40 Display : 4.3” True colour TFT display with touch screen Temperature Range : -40 to 120°C @23°C Ambient Resolution : 0.01 °C Block Stability : Better than ± 0.03°C at full range Block Radial Uniformity : ± 0.02°C at full range Block Axial Uniformity (upto 40mm) : ± 0.18°C at -45°C ± 0.1°C at 0°C ± 0.05°C at 50°C ± 0.11°C at 100°C ± 0.17°C at 120°C Temperature Read out : °C / °F (selectable) Loading effect: Better than ± 0.08°C hysteresis: Better than ± 0.03°C Cooling time : 30 mins (25 to -45 °C) 15 mins (25 to -30 °C) 65 mins (120 to 25 °C) Heating time : 25 mins (25 to 120 °C) 75 mins (-45 to 120 °C) 52 mins (-45 to 25 °C) Stabilization time: 10 minutes Insert (Dia. x Height): 30 x 160 mm Test sensor immersion depth: 130 mm Standard well holes in mm: Insert No. 1 → 5.1, 6.2, 6.2 & 8.1, Insert No. 2 → 6.2, 6.2 & 10.2 Measure inputs: RTD-PT 100, PT 1000 / TC - J, K, R, S, T, E, B , N , Analog – mA, V, mV, ohms Cold junction Accuracy: ± 0.3°C UUC Sensor supply input: 24V DC ± 10% / 50mA max. Power supply: 230V AC ± 10% / 50Hz (optional 110V AC) Power Consumption: 500 VA Switch Test : Provided Overall Dimension in mm: 390 x 185 x 356 (L x B x H) (Approx.) Weight: 17.3 kg (with well insert) (Approx.)