Thank you for writing to us. One of our executive will reach back to you through your submitted medium. In case there’s an urgency, feel free to connect over WhatsApp for faster response.
Model: ORP 300
Display: 0.5” 3 ½ Digit 7 segment Red LED
Range: -1999 to +1999 mV
Resolution: 1 mV
Accuracy: ± 1 mV ± 1 digit
Input Impedance: > 10¹² Ohms
Input connection: BNC socket
Electrode: ORP Electrode with BNC attachment
Operating Environment: 0 to 50 °C / 20 to 95 % RH non condensing
Power supply: 230V AC / 50 Hz ± 10%
Overall Dimensions in mm: 185 x 235 x 65 (L x B x H)
Instrument weight: 1.6 kg (Approx.)
Model: TDS 602-1
Display: 4 + 4 Digit 0.5” & 0.39” 7-Segment Red LED Display
Cell Constant*: 0.01 / 0.1 / 1 (user selectable, depends on range)
Range (any one): 1–20 ppm, 5–200 ppm, 10–2000 ppm, 1–20 ppt, 5–200 ppt
Accuracy: ±1% of range +1 digit
Resolution: 0.01 ppm to 0.1 ppt (depends on range)
Temperature Sensor: RTD – PT100 (3-wire)
Temperature Coefficient: 0 to 3% / °C (user adjustable)
Temperature Compensation: Manual / Automatic (-20.0 to +150.0 °C)
Electrode Input: Conductivity cell on rear panel
Set Point – 1 & 2: Two set points with 6 relay status selectable
Relay Output: Relay-1 for Setpoint-1, Relay-2 for Setpoint-2 with 5A rating
Relay Hysteresis: 0 to 500 counts (user adjustable) (only for High & Low control modes)
Relay Cyclic Delay: 0 to 100 seconds (user adjustable) (only for High & Low control modes)
Alarm Output (optional): Inbuilt audible buzzer with front-key reset
Optional Re-Tx Output: Galvanically isolated 4–20 mA
Optional Comm. Output: Isolated RS-485
Communication Protocol: MODBUS RTU
Operating Environment: -10 to 50 °C / 10 to 95% RH non-condensing
Power Supply: 90 to 270 V AC / DC, 50 Hz
Enclosure: ABS plastics
Dimension: 96 × 96 × 85 mm
Cutout Dimension: 92 × 92 mm
Weight: 350 grams (Approx.)
Model: ORT 601-1
Display: 4 + 4 Digit 0.5” & 0.39” 7-Segment Red LED Display
Range: -1999 to 1999 ORP
Accuracy: ±1 ORP ±1 digit
Resolution: 1 ORP
Electrode Input: Platinum electrode with BNC attachment
Set Point – 1 & 2: Two set points with 6 relay status selectable
Relay Output: Relay-1 for Setpoint-1, Relay-2 for Setpoint-2 with 5A rating
Relay Hysteresis: 0 to 5 ORP (user adjustable) (only for High & Low control modes)
Relay Cyclic Delay: 0 to 100 seconds (user adjustable) (only for High & Low control modes)
Input Impedance: >10¹² ohms
Alarm Output (optional): Inbuilt audible buzzer with front-key reset
Optional Re-Tx Output: Galvanically isolated 4–20 mA
Optional Comm. Output: Isolated RS-485
Communication Protocol: MODBUS RTU
Operating Environment: -10 to 50 °C / 10 to 95% RH non-condensing
Power Supply: 90 to 270 V AC / DC, 50 Hz
Dimension: 96 × 96 × 85 mm
Cutout Dimension: 92 × 92 mm
Weight: 350 grams (Approx.)
Model: CC 603 - 1
Display: 4 + 4 Digit 0.5” & 0.39” 7 Seg RED LED Display
Range (any one): 1 – 20µS, 5 – 200µS, 10 to 2000µS, 1 to 20mS, 5 to 200mS
Resolution: 0.01µS to 0.1mS (depends on range)
Accuracy: ±1% of range ±1 digit
Cell Constant*: 0.01 / 0.1 / 1 (user selectable, depends on range)
Temperature Sensor: RTD – PT 100 (3 wire)
Temperature Co-efficient: 0 to 3% / °C (user adjustable)
Temperature Compensation: Manual / Automatic (-20.0 to +150.0°C)
Electrode Input: Conductivity cell on rear panel
Set Point – 1 & 2: Two set points with 6 relay status selectable
Relay Output:
Relay-1 for Setpoint-1, Relay-2 for Setpoint-2 with 5A rating
Relay Hysteresis: 0 to 500 counts (user adjustable)
(only for High & Low control modes)
Relay Cyclic Delay: 0 to 100 seconds (user adjustable)
(only for High & Low control modes)
Alarm Output (optional): Inbuilt audible buzzer with front key reset
Optional Re-Tx Output: Galvanically isolated 4 – 20 mA
Optional Comm. Output: Isolated RS-485
Comm. Protocol: MODBUS RTU
Operating Environment: -10 to 50°C / 10 to 95% RH non-condensing
Power Supply: 90 to 270V AC / DC, 50Hz
Dimension: 96 × 96 × 85 mm
Cutout Dimension: 92 × 92 mm
Weight: 350 grams (Approx.)
Model : HTP 196
Display : 3 line 4digit ,0.5” 7 segment LED
Range : 0 to 60°C / 0to100%RH/ 0 to 2000mbarA
Resolution : 0.01 or 0.1°C / 0.1% RH / 1 mbar
Accuracy : ± 0.5 °C / ± 3%RH / ± 0.5 % FS
Mounting : Wall mountable
Power supply : 90 to 270V AC
Dimension : 100 mm W x 250 mm H x60 mm D
Weight : 640gms
Sensor : P T-100, Humidity & Pressure sensor with 2 meter cable
Model : pH 600 - 1
Display : 4 + 4 Digit 0.5” & 0.39” 7 Seg RED LED Display
Input Impedance : >10 Ohms
Range : -2 to 16 pH
Resolution : 0.01 pH
Temperature sensor: RTD - PT 100 (3 wire)
Temp. Compensation: Manual / Automatic (-20.0 to +150.0ºC)
Electrode Input: Combined Electrode with BNC Attachment
Accuracy : ± 0.01 pH ± 1 digit
Set Point - 1 & 2: Two Set Point with 6 Relay Status Selectable
Relay Output : Relay - 1 for Setpoint - 1, Relay - 2 for Setpoint - 2 with 5A Rating
Relay Hysteresis : 0 to 5 pH (user adjustable)(only for High & Low control modes)
Relay Cyclic delay : 0 to 100 seconds (user adjustable)(only for High & Low control modes)
Alarm Output(optional) inbuilt audible buzzer with front key reset
Optional Re. Tx. output Galvanically Isolated : 4 - 20 mA
Optional Comm. output Isolated RS 485
Comm. Protocol MODBUS RTU
Operating Environment : -10 to 50ºC / 10 to 95 % RH Non Condensing
Power Supply : 90 to 270V AC / DC 50Hz
Dimension : 96 x 96 x 85 mm.
Cutout Dimension : 92 x 92 mm
Weight : 500 grams (Approx.)
Model: PI – 541A
Display: 6 Digit 7 segment RED LED
Inputs: 0 - 20 mA, 0 to 75 mV, -10 to 10 V DC, 0 – 4000 Ω (H & L Limit Programmable)
RTD - PT 100, PT-1000, Thermocouple - J, K, R, S, T, B, N, E
Cold junction Accuracy: ± 0.3°C
Resolution: 0.0001 / 0.001 / 0.01 / 0.1 / 1°C Selectable for Analog
0.01°C for RTD and 0.1°C for TC
Unit selection: °C / °F (for RTD & TC inputs)
Linearization: Programmable custom Linearization provided (1 - 21 points)
Input signal filter: 1 – 100% user configurable
Cold junction compensation: Automatic inbuilt ‘CJC’ is provided
Relay Output* (optional): 2 Relay (5A rated) with 4 Relay Status Selection, Hysteresis, Cyclic Delay
Alarm settings: Front key settable
Alarm indication : Two LED on front panel
Re Transmission* (optional): Opto Isolated Analog Output 4 - 20 mA or 0 - 10V DC for process variable
PC communication* (optional): RS 485 (2 wire) MODBUS protocol
PC Software* (optional): Monitoring, Data logging, Report & graph
Sensor excitation Supply: 24 V DC ±10% @ 100 mA
Power supply: 90 to 270 V AC / DC / 50/60 Hz
Front panel : IP 65 protection
Operating environment: 0 to 50°C / 5 to 95% RH non condensing
Overall Dimensions: 48(H) X 96(W) X 110(D) mm
Cut out Dimension: 44(H) x 90(W) mm
Enclosure: ABS plastic
Weight: 350 grams (Approx.)
SANSEL Model TCAL 1405 / -30 Dry well Temperature calibrator are high performance for industrial and Laboratory atmosphere and covering temperature range from -30* to 100°C. Which are ideally suited onsite calibration of thermocouple, RTDs, Indicator with sensors & 4-20mA signal transmitter with sensor & indicator in Food, Pharmaceutical and all types of process industries and Calibration Laboratories. Having it’s advantage of user friendly, light weight, portable, fast settling, better uniformity and accuracy over a wide temperature range. TCAL 1405 / -30 having interchangeable inserts to suit for calibration of different diameter of sensors. Additional Inserts (optional) with special drillings are available on request.
Technical Specifications :
Model: TCAL 1405 / - 30
Temperature Range: -30* to 100°C (* @ Ambient 25 °C)
Resolution: 0.01°C
Display: 3.5“ True TFT Multi colour touch screen display
Temperature readout: °C / °F
Block Stability: ± 0.03°C
Axial Uniformity upto 40mm: ± 0.06 °C (from -30 to 50 °C), ± 0.1 °C (from 51 to 100 °C)
Radial Uniformity: ± 0.05°C
Loading Effect: ± 0.04°C
Hysteresis: ± 0.02°C
Well Dimension (dia. x height x hole depth): 25 x 145 x 130 mm
Standard well holes in mm: 6.2 x 3nos, 8.1 x 1nos
Power supply: 230V AC ± 10% / 50Hz (Optional 110V AC), 500 W
Overall Dimension in mm: 142.0 x 233.5 x 271.5 (L x B x H)(Approx.)
Instrument Weight: 8 kg (Approx.)
Model: TCAL 1501/ - 40
Display: 3.5 inch True TFT LCD Display with Touch screen
Temperature Range: -40 to 50°C
Resolution: 0.01°C
Heating & Cooling medium: ETHYLENE GLYCOL HOCH2CH2OH purity 99% (3litres) + Pure distilled water (1.5 litres ) for range from - 40 to 50 °C
Stability: ± 0.05°C
Uniformity: ± 0.2°C
Stabilization Time: 15 minutes
Heating time: 30 mins
Cooling time: 60 mins (amb. (25°C to - 40°C ) @25°C
Multi hole PP top cover: Provided for test Thermometer or sensor holding
Power supply: 230V AC 50/60Hz
Power Consumption: 1300 VA
Calibration chamber size: 90 W x 120 H x 175 D mm
Overall Dimension: 530 x 340 x 670 (L x W x H) (+155mm circulation motor) (Approx.)
Weight: 52 kg (without liquid)